{"title":"Chevrolet Silverado Parts","description":"\u003cp\u003e53 3D-printable replacement parts for the Chevrolet Silverado (1988–2025 models), including cup holder, seat recline lever, dash power center insert and hood bump stop. Every part is printed to order to replace broken, worn or discontinued originals.\u003c\/p\u003e\u003cp\u003eCan't find your part? \u003ca href=\"\/pages\/contact\"\u003eRequest it\u003c\/a\u003e. See all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet parts\u003c\/a\u003e.\u003c\/p\u003e","products":[{"product_id":"dash-power-center-insert-1988-chevrolet-silverado","title":"Dash Power Center Insert – 1988 Chevrolet Silverado","description":"\u003cp\u003e3D-printed replacement dash power center insert made for the 1988 Chevrolet Silverado: a simple way to replace a cracked, lost or hard-to-find original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eI need a power center other than the cigarette lighter for my 1988 truck since the cigarette lighter is always powered on and I wanted to have an outlet that the power was switched with the ignition so items attached wouldn't run down the battery. This design provides for several options one of which is a cigarette style power outlet that I can use for my tire pressure guage. I found the USB charge port module that fits a Toyota that are an insert that simply pushes in and locks witch includes a volt meter - Very convenient for charging phones.\u003cbr\u003e\u003cbr\u003eDashboard insert for the 1U space under the center vent on a 1988 Chevy truck. I used a relay and connected the control line to one of the switched connectors on the courtesy panel under the dash on the drivers side so that all of the items on the panel turn off with the truck ignition. \u003cbr\u003e\u003cbr\u003eI had to design new locking rings to hold the panel meter and cigarette lighter to the panel since there wasn't enough room to fit the rings that came with these items - I designed them in Fusion 360 and used the thread specification from the menu however I found that when they were printed, they were a little sloppy therefore I scaled them on the print to 99% which took out the slop.\u003cbr\u003e\u003cbr\u003e The reason I used the Elk relay was that it's a compact size and has screw terminals which makes it easier for wiring. The Elk relay that I used can be substituted for a relay that handles more amps however it would probably need to be mounted outside of the insert.\u003cbr\u003e\u003cbr\u003eI left a square hole in the back since I have a programmable ECM and I wanted to be able to string the (RJ7) connector through it.\u003cbr\u003e\u003cbr\u003eI used 8 x 1\" pan head screws to secure the insert from the front - One word of caution, the left screw is accessed through the Toyota power center hole. Once the power center is snapped into place, it's extreamly hard to get to the screw since the release for the power center is from behind. Be sure that you aren't planning on removing the insert without removing the Chevy panel and accessing the screw from behind since it's not gong to be easy (Sorry about that ). Maybe a better solution is to only use the center screw accessed through the opening.\u003cbr\u003e\u003cbr\u003eHere is the part number to the screws I used from Panther RV:\u003cbr\u003eSTW-8X1-100 Stainless Pan Head Screw Philips Head White 100 Pk\u003cbr\u003e\u003cbr\u003eI just happened to have these screws on my bench and they worked :-) Drill a small pilot hole in the back panel before screwing these through the insert which makes installation easier.\u003cbr\u003e\u003cbr\u003eI'm not going to link to these items since they eventually break so I am putting the specifications and pictures here so that they can be found.\u003cbr\u003e\u003cbr\u003eElk Products Relay:\u003cbr\u003eContact Type \tSpdt\u003cbr\u003eCurrent Rating \t10 Amps\u003cbr\u003eMounting Type \tDoor Mount\u003cbr\u003eBrand \tElk\u003cbr\u003eOperation Mode \tElectric\u003cbr\u003eProduct details\u003cbr\u003e\u003cbr\u003e    Is Discontinued By Manufacturer ‏ : ‎ No\u003cbr\u003e    Product Dimensions ‏ : ‎ 1.5 x 2 x 0.5 inches; 0.01 ounces\u003cbr\u003e    Item model number ‏ : ‎ 912\u003cbr\u003e    Date First Available ‏ : ‎ July 15, 2010\u003cbr\u003e    Manufacturer ‏ : ‎ ELK Products Inc\u003cbr\u003e    ASIN ‏ : ‎ B002Z8GX92\u003cbr\u003e\u003cbr\u003e    Best Sellers Rank: #265,329 in Industrial \u0026amp; Scientific (See Top 100 in Industrial \u0026amp; Scientific)\u003cbr\u003e        #483 in Electromechanical Relays\u003cbr\u003e\u003cbr\u003eToyota Charge Port:\u003cbr\u003eMICTUNING Upgraded Dual USB Port 6.4A QC3.0 Quick Charger with Blue LED Digital Voltmeter Replacement for Toyota, Compatible with Cellphone iPad PDA Laptop GPS (Surface Size 1.3 x 0.9 inches) \u003cbr\u003e\u003cbr\u003eI hope you find this design useful - Thanks for looking.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1988 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eDash Power Center Insert\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1988\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e2 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-6acbabb8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:6691824\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015766831336,"sku":"CAT-6acbabb8","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/dash-power-center-insert-1_1783512293184_4r5f4p.jpg?v=1793141245"},{"product_id":"hood-bump-stop-1988-2000-chevrolet-silverado-gmt400","title":"Hood Bump Stop – 1988-2000 Chevrolet Silverado GMT400","description":"\u003cp\u003eNeed a replacement hood bump stop for your 1988-2000 Chevrolet Silverado GMT400? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eHood bump stop to flush hood, GM part 10309494, fits various GM trucks\/SUVs.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1988-2000 Chevrolet Silverado GMT400\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eHood Bump Stop\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1988\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-dd83ce71\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:7298878\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015767748840,"sku":"CAT-dd83ce71","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/hood-bump-stop-1_1783419135172_0ynkws.jpg?v=1793141246"},{"product_id":"underhood-retractable-light-locking-arm-1988-1999-chevrolet-silverado-gmt400","title":"Underhood Retractable Light Locking Arm – 1988-1999 Chevrolet Silverado GMT400","description":"\u003cp\u003eNeed a replacement underhood retractable light locking arm for your 1988-1999 Chevrolet Silverado GMT400? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eReplacement locking arm for retractable underhood light on Chevrolet\/GMC trucks.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1988-1999 Chevrolet Silverado GMT400\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eUnderhood Retractable Light Locking Arm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1988\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e2 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-736dd218\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4784719\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015767847144,"sku":"CAT-736dd218","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/underhood-retractable-light-locking-arm-1_1783419145224_exmrsp.jpg?v=1793141247"},{"product_id":"cup-holder-1996-chevrolet-silverado","title":"Cup Holder – 1996 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing cup holder on your 1996 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis cup holder not only has a space for a cup, but it also has a little storage that you can use for coins or other things, this has been tested to fit perfectly into the vehicle.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1996 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eCup Holder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1996\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-aa83bd17\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:6931763\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015768076520,"sku":"CAT-aa83bd17","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/cup-holder-1_1768164848590_cj8pdd.jpg?v=1793141248"},{"product_id":"door-handle-1998-chevrolet-silverado","title":"Door Handle – 1998 Chevrolet Silverado","description":"\u003cp\u003eNeed a replacement door handle for your 1998 Chevrolet Silverado? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eDesigned this door handle replacement because mine broke. It isn't an exact match because that wasn't needed.\u003cbr\u003e\u003cbr\u003ePrinting:\u003cbr\u003e\u003cbr\u003ePrinted with 50% infill, can probably be printed with lower infill.\u003cbr\u003e\u003cbr\u003eNotes:\u003cbr\u003e\u003cbr\u003eI already had the plastic washer that holds the rod, so that isn't included. \u003cbr\u003eIf you don't have it, you may want to edit that part in the .SLDPRT file.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1998 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eDoor Handle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1998\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-7982294e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4970163\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015768142056,"sku":"CAT-7982294e","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/door-handle-1_1783494161547_2lv6rr.jpg?v=1793141249"},{"product_id":"equalizer-knob-1998-chevrolet-silverado","title":"Equalizer Knob – 1998 Chevrolet Silverado","description":"\u003cp\u003eNeed a replacement equalizer knob for your 1998 Chevrolet Silverado? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThere's a version with and a version without the ridges, depending on your printer. They friction fit, so you've got to press pretty hard to pop them in.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1998 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eEqualizer Knob\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1998\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e2 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-f39cb160\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:7100970\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015768502504,"sku":"CAT-f39cb160","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/equalizer-knob-1_1769311860115_7zrhc4.jpg?v=1793141249"},{"product_id":"tailgate-handle-rod-clips-1998-chevrolet-silverado","title":"Tailgate Handle Rod Clips – 1998 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing tailgate handle rod clips on your 1998 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis is a tailgate handle rod clip for chevy trucks, it should fit any 1981-1998 C\/K 1500, 2500, or 3500. I designed this after buying an old 98 silverado, and found that it was missing one of these clips, which kept the tailgate handle from working properly. Hopefully some of you will find it helpful.\u003cbr\u003eI printed this with regular pla on an ender 3, doesn't require anything special outside of supports. You will most likely need to file it a little bit on some spots to make everything fit easily, but when i printed it it was pretty much good to go.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1998 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eTailgate Handle Rod Clips\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1998\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e2 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-2b7b482a\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:5275113\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015772500200,"sku":"CAT-2b7b482a","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/tailgate-handle-rod-clips-1_1768164645062_qcxlz5.jpg?v=1793141250"},{"product_id":"cargo-and-fog-light-switch-panel-1999-2006-chevrolet-silverado","title":"Cargo And Fog Light Switch Panel – 1999-2006 Chevrolet Silverado","description":"\u003cp\u003e3D-printed cargo and fog light switch panel for the 1999-2006 Chevrolet Silverado, made to order as an affordable alternative to a discontinued or expensive original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eI designed it to replace the cargo and fog light switch on my Chevy Silverado 2000.\u003cbr\u003eIt can fit on all Chevy and GMC truck models from 99 to 2006.\u003cbr\u003eI use a 16mm switch to get 3 button spaces for (top roof light, cargo light, fog lamp).\u003cbr\u003e\u003cbr\u003eYou can buy the switches from AliExpress from the link below.\u003cbr\u003ehttps:\/\/m.aliexpress.com\/item\/1005001797766139.html?spm=a2g0n.order_list.order_list_main.45.3e8b1802RMJcXR\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1999-2006 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eCargo And Fog Light Switch Panel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1999\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-79749c6f\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:5651775\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015772827880,"sku":"CAT-79749c6f","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/cargo-and-fog-light-switch-panel-1_1778051722929_brlaa3.jpg?v=1793141251"},{"product_id":"cubby-two-holes-are-better-than-one-1999-chevrolet-silverado","title":"Cubby Two Holes Are Better Than One – 1999 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing cubby two holes are better than one on your 1999 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eRemix of BurasPrints' Silverado Cubby Gauge Pod.  This is fits two barrel mount, e.g. USB ports, devices.\u003cbr\u003e\u003cbr\u003e\"It's the cubby just below the center dash vent. Not on all Silverado's though. Once you remove the old cubby, you need to remove the old clips which can be a pain. But are necessary to a good fitment in your truck.\u003cbr\u003e\u003cbr\u003eReplaces GM15766229 Cubby so check to see if this looks like yours.\"\u003cbr\u003e\u003cbr\u003eI used one of each of these:\u003cbr\u003ehttps:\/\/www.ebay.com\/itm\/285021151594\u003cbr\u003ehttps:\/\/www.ebay.com\/itm\/284216777328\u003cbr\u003e\u003cbr\u003eNote the two hole sizes are not the same.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1999 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eCubby Two Holes Are Better Than One\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1999\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-b2d5fe2e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:6126235\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015772926184,"sku":"CAT-b2d5fe2e","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/cubby-two-holes-are-better-than-one-1_1783491057880_du9a0j.jpg?v=1793141253"},{"product_id":"key-fob-cover-1999-2007-chevrolet-silverado","title":"Key Fob Cover – 1999-2007 Chevrolet Silverado","description":"\u003cp\u003eNeed a replacement key fob cover for your 1999-2007 Chevrolet Silverado? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eI needed a cover for a 1999-2007 GM silverado key as my loop had broken. This will slip on the key and allow the key ring to pass through. It will fit many different year and model GM keys. I printed it with Ninjaflex at .200 micron and 100% infill. Print vertical so the only bridge is the straight part of the key ring hole.\u003cbr\u003e\u003cbr\u003eThis is a work in progress. I will update the design later.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1999-2007 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eKey Fob Cover\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1999\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-3bb11f2a\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:3647697\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015773188328,"sku":"CAT-3bb11f2a","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/key-fob-cover-1_1783494156604_tbu47z.jpg?v=1793141253"},{"product_id":"overhead-console-panel-insert-1999-chevrolet-silverado","title":"Overhead Console Panel Insert – 1999 Chevrolet Silverado","description":"\u003cp\u003e3D-printed replacement overhead console panel insert made for the 1999 Chevrolet Silverado: a simple way to replace a cracked, lost or hard-to-find original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eMade to go in 99+ Chevy Silverado overhead consoles in the front where the optional compass \/ dead panel  normally lives. i've included a blank panel that you can modify to accept anything you'd like, and also my set up that accepts a 30mm voltage gauge, 16mm switch, and a CYD\u003cbr\u003e\u003cbr\u003ePrinted mine in ABS,\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1999 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eOverhead Console Panel Insert\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1999\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e2 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-6beca244\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:7230579\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015773253864,"sku":"CAT-6beca244","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/overhead-console-panel-insert-1_1778051714579_qmoxy4.jpg?v=1793141254"},{"product_id":"rear-vent-extenders-1999-chevrolet-silverado","title":"Rear Vent Extenders – 1999 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing rear vent extenders on your 1999 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eFirst uploaded files--\u003cbr\u003e\u003cbr\u003eThis is result of a remix originally posted by 737mechanic. \u003cbr\u003eI remodeled this in Creo software to get a smoother flow, and add my namesake to the part.\u003cbr\u003e\u003cbr\u003ePrint time on my machine 1hr 37mins using AnkerMake app slicer. Fast setting 10% infill\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1999 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eRear Vent Extenders\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1999\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e2 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-0ae246bb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:6800972\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015773516008,"sku":"CAT-0ae246bb","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/rear-vent-extenders-1_1783516243274_o22oxs.jpg?v=1793141255"},{"product_id":"rear-window-latch-1999-2003-chevrolet-silverado","title":"Rear Window Latch – 1999-2003 Chevrolet Silverado","description":"\u003cp\u003e3D-printed rear window latch for the 1999-2003 Chevrolet Silverado, made to order as an affordable alternative to a discontinued or expensive original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis latch should fix the wind noise coming from rear windows in Chevrolet Silverados between 1999 and 2003 (?).  It is about 1mm longer than the original so it pulls the window shut just a little further.  I tested this in my Silverado and the wind noise is much less than it was with the original piece.\u003cbr\u003e\u003cbr\u003eI printed this out of PLA with 100% infill.  I think it should be alright but I'm not sure what will happen in the summer when temperatures get over 100F degrees.  The PLA may become a little malleable.  Maybe a different material, like PETG, would be better... I'm not sure, I'll find out.\u003cbr\u003e\u003cbr\u003eI saw something similar to this for sale online for over $30, but it looked simple enough to try to design and print, not to mention way cheaper.  On YouTube, search for \"silverado wind noise\" for some videos that show how to replace it.\u003cbr\u003e\u003cbr\u003eIf it works for you, please click like and let me know in the comments or by clicking the \"Like\" button.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1999-2003 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eRear Window Latch\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1999\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-d9982aed\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:2846613\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015773614312,"sku":"CAT-d9982aed","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/rear-window-latch-1_1778051753595_krh4x7.jpg?v=1793141255"},{"product_id":"sierra-thermos-stabilizer-1999-chevrolet-silverado","title":"Sierra Thermos Stabilizer – 1999 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing sierra thermos stabilizer on your 1999 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eWood PLA\u003cbr\u003e20 micron layer\u003cbr\u003e\u003cbr\u003eVid of it in action\u003cbr\u003ehttps:\/\/goo.gl\/photos\/7YjHTSVqmdvLcVj76\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1999 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eSierra Thermos Stabilizer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1999\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-ff4845e1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:2406255\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015773876456,"sku":"CAT-ff4845e1","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/sierra-thermos-stabilizer-1_1783494141726_b6clv9.jpg?v=1793141257"},{"product_id":"tailgate-repair-linkage-clip-1999-2025-chevrolet-silverado","title":"Tailgate Repair Linkage Clip – 1999-2025 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing tailgate repair linkage clip on your 1999-2025 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eTailgate repair linkage clip for Chevrolet Silverado.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1999-2025 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eTailgate Repair Linkage Clip\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1999\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-f681dd94\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:998114\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015774171368,"sku":"CAT-f681dd94","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/tailgate-repair-linkage-clip-1_1783502631344_2x0gry.jpg?v=1793141258"},{"product_id":"headlight-hvac-control-knobs-switch-panel-2000-chevrolet-silverado","title":"Headlight \/ Hvac Control Knobs \u0026 Switch Panel – 2000 Chevrolet Silverado","description":"\u003cp\u003eNeed a replacement headlight \/ hvac control knobs \u0026amp; switch panel for your 2000 Chevrolet Silverado? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eDesigned these to fit my 2000 Chevy Silverado. Pretty basic design that I thought looked nice.\u003cbr\u003eThe \"insert\" was snug enough that a press fit will hold it in place with no adhesive.\u003cbr\u003eUse the test prints to make sure the knobs fit snug. HVAC controls will reuse metal inserts on factory knobs.\u003cbr\u003eThe switch panel is only for use with vehicles equipped with floor mounted 4x4 control. This will replace the \"wallet\" pocket to the left of the steering wheel.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2000 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eHeadlight \/ Hvac Control Knobs \u0026amp; Switch Panel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e3 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-e70c88c8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003ePrinter\u003cbr\u003eBrand: Prusa\u003cbr\u003ePrinter: I3 MK3S\u003cbr\u003eRafts: No Supports: No Resolution: 200 Infill: 20 Filament: Prusament PLA Black \/ White\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4920373\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015774335208,"sku":"CAT-e70c88c8","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/headlight-hvac-control-knobs-switch-panel-1_1768164688838_d60g5s.jpg?v=1793141258"},{"product_id":"heater-hose-removal-tool-2000-chevrolet-silverado","title":"Heater Hose Removal Tool – 2000 Chevrolet Silverado","description":"\u003cp\u003e3D-printed heater hose removal tool for the 2000 Chevrolet Silverado, made to order as an affordable alternative to a discontinued or expensive original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eI needed the tool to be able to take the heater core pipes off the firewall.\u003cbr\u003e\u003cbr\u003eFinding one proved to be hard so I made one.\u003cbr\u003e\u003cbr\u003eMake 2 of these and then slide them in between the pipe and the plastic part of the hose.\u003cbr\u003eDon't make the mistake of pulling on the tool, just slide the tool in and then pull on the hose.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2000 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eHeater Hose Removal Tool\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-10be252e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:6688591\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015774564584,"sku":"CAT-10be252e","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/heater-hose-removal-tool-1_1783515063974_c13r67.jpg?v=1793141259"},{"product_id":"interior-trim-insert-panel-2000-chevrolet-silverado","title":"Interior Trim Insert Panel – 2000 Chevrolet Silverado","description":"\u003cp\u003e3D-printed interior trim insert panel for the 2000 Chevrolet Silverado, made to order as an affordable alternative to a discontinued or expensive original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis is an interior piece for a 2000 Chevrolet Silverado and similar vehicles. The original reason for printing it was to hold a remote to control fog lights on a remote relay, however I am uploading the design without holes, and the solidworks files so anyone can change it to suit their needs if they so desire. If you need another file type, let me know and I'll upload a version of it for you. \u003cbr\u003e\u003cbr\u003eHere is a link to the specic remote relay used if you would like to do something similar:\u003cbr\u003ehttps:\/\/www.amazon.com\/iMBAPrice-Heavy-Universal-Remote-Control\/dp\/B00LMICSIQ\/ref=sr_1_1?ie=UTF8\u0026amp;qid=1490412033\u0026amp;sr=8-1\u0026amp;keywords=heavy+duty+universal+12+volt+remote+control+kit\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2000 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eInterior Trim Insert Panel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e2 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-7f3cc826\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:2202388\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015774597352,"sku":"CAT-7f3cc826","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/interior-trim-insert-panel-1_1778051727898_vwrbsc.jpg?v=1793141260"},{"product_id":"center-console-rear-cubby-2001-2006-chevrolet-silverado-gmt800","title":"Center Console Rear Cubby – 2001-2006 Chevrolet Silverado GMT800","description":"\u003cp\u003e3D-printed center console rear cubby for the 2001-2006 Chevrolet Silverado GMT800, made to order as an affordable alternative to a discontinued or expensive original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis part was designed after the now obsolete GM rear cubby for GMT 800 bodied Chevrolet Silverado trucks. \u003cbr\u003e\u003cbr\u003ehttps:\/\/www.duramaxforum.com\/threads\/how-to-delete-center-console-rear-audio-controls.228417\/\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2001-2006 Chevrolet Silverado GMT800\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eCenter Console Rear Cubby\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2001\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-1ce0fe0e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4259408\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015774826728,"sku":"CAT-1ce0fe0e","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/center-console-rear-cubby-1_1783494137624_hkyp3m.jpg?v=1793141262"},{"product_id":"dash-cb-radio-bezel-2001-2006-chevrolet-silverado","title":"Dash Cb Radio Bezel – 2001-2006 Chevrolet Silverado","description":"\u003cp\u003e3D-printed replacement dash cb radio bezel made for the 2001-2006 Chevrolet Silverado: a simple way to replace a cracked, lost or hard-to-find original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis is a bezel for a Galaxy 979 CD radio installed in a Chevrolet Silverado dash cubby. It also has a cutout for a twin port USB port. To do the install the back of the cubby needs to be cut out.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2001-2006 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eDash Cb Radio Bezel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2001\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-5369c54a\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4259419\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015775121640,"sku":"CAT-5369c54a","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/dash-cb-radio-bezel-1_1778307221656_19etob.jpg?v=1793141262"},{"product_id":"gas-door-bump-stops-2001-chevrolet-silverado","title":"Gas Door Bump Stops – 2001 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing gas door bump stops on your 2001 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003egas door bump stops for a 01 Silverado, print in tpu.. no support needed..\u003cbr\u003e\u003cbr\u003eput a drop of oil on the bump stop taper and pull it through the quarter...\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2001 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eGas Door Bump Stops\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2001\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-f37a52e1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:3120862\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015775285480,"sku":"CAT-f37a52e1","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/gas-door-bump-stops-1_1778051733647_kpotuv.jpg?v=1793141263"},{"product_id":"radio-tuner-knob-2001-chevrolet-silverado","title":"Radio Tuner Knob – 2001 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing radio tuner knob on your 2001 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis is the Tuner knob for an 2001 Chevy Silverado Radio. It should work on any standard Chevy radio.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2001 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eRadio Tuner Knob\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2001\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-a123a5f3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:1023341\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015776071912,"sku":"CAT-a123a5f3","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/radio-tuner-knob-1_1778051757085_xtlgzr.jpg?v=1793141264"},{"product_id":"cup-holder-extension-2003-chevrolet-silverado-ss","title":"Cup Holder Extension – 2003 Chevrolet Silverado (SS)","description":"\u003cp\u003eNeed a replacement cup holder extension for your 2003 Chevrolet Silverado (SS)? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eGot tired of water bottles tipping over in my 2003 Silverado SS. Made a snug extension so it doesn't anymore.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2003 Chevrolet Silverado (SS)\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eCup Holder Extension\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2003\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-9493f059\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:3469726\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015776170216,"sku":"CAT-9493f059","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/cup-holder-extension-1_1778307236171_x56r9d.jpg?v=1793141265"},{"product_id":"dash-cubby-2003-chevrolet-silverado","title":"Dash Cubby – 2003 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing dash cubby on your 2003 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eRemixed from Buras Prints awesome model, I added the SS logo to mimic the factory SS inserts while still allowing for both blanks to mount switches or use a gauge. Also added a version with a GMC logo for the Sierra\/Yukon folks. If you need one without logos, please go download the original model this was remixed from!\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2003 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eDash Cubby\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2003\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-56a2bbc4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:6811302\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015776366824,"sku":"CAT-56a2bbc4","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/dash-cubby-4_1767928481369_wqfyop.jpg?v=1793141266"},{"product_id":"overhead-console-gauge-pod-2003-chevrolet-silverado","title":"Overhead Console Gauge Pod – 2003 Chevrolet Silverado","description":"\u003cp\u003e3D-printed replacement overhead console gauge pod made for the 2003 Chevrolet Silverado: a simple way to replace a cracked, lost or hard-to-find original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eDesigned this for use in a 2003 chevy silverado. Its an overhead console gauge pod. It will fit 2\" gauge pods.\u003cbr\u003e\u003cbr\u003ePrinted with PETG\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2003 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eOverhead Console Gauge Pod\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2003\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-20506fa3\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4654782\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015776465128,"sku":"CAT-20506fa3","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/overhead-console-gauge-pod-1_1778051766092_mc8pfe.jpg?v=1793141266"},{"product_id":"radio-knob-2003-chevrolet-silverado","title":"Radio Knob – 2003 Chevrolet Silverado","description":"\u003cp\u003e3D-printed replacement radio knob made for the 2003 Chevrolet Silverado: a simple way to replace a cracked, lost or hard-to-find original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eMade this to replace the broken\/missing knob on my 2003 Chevy Silverado BOSE 6 CD Changer Radio. Made it a little loose and put a drop of glue in it to hold it. Works great, looks great.\u003cbr\u003eDesigned with Sketchup. Printed with Black Hatchbox PLA with a 10% infill.\u003cbr\u003eIf you print this please post a photo!\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2003 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eRadio Knob\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2003\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-13cfff2a\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:5478973\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015776694504,"sku":"CAT-13cfff2a","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/radio-knob-1_1768158566636_3a7ohb.jpg?v=1793141267"},{"product_id":"battery-hold-down-2004-chevrolet-silverado","title":"Battery Hold Down – 2004 Chevrolet Silverado","description":"\u003cp\u003eNeed a replacement battery hold down for your 2004 Chevrolet Silverado? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eGM Battery Hold Down 14005061 for a multitude of models including GMC, Chevrolet, Cadillac, Buick, Pontiac, Saturn, Hummer.\u003cbr\u003e\u003cbr\u003eI needed one for our 2004 Silverado, you might need it for a Sierra, Suburban, Tahoe, or maybe even a Corvette!\u003cbr\u003e\u003cbr\u003eTypically uses an  M8 x 45mm hex-washer head bolt with a thread pitch of 1.25.\u003cbr\u003e\u003cbr\u003eIf You make one please post it :)\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2004 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eBattery Hold Down\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2004\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-3b18387e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:2935938\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015776923880,"sku":"CAT-3b18387e","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/battery-hold-down-1_1778130280211_7h9n2m.jpg?v=1793141268"},{"product_id":"cup-holder-2006-chevrolet-silverado","title":"Cup Holder – 2006 Chevrolet Silverado","description":"\u003cp\u003e3D-printed cup holder for the 2006 Chevrolet Silverado, made to order as an affordable alternative to a discontinued or expensive original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis fits in place of the factory cup holder in the center console for an 06 gmc\/ chevy full size truck. will fit other years. 2 cup holder in the back fit a 30 oz yetti cup and the front cup holders fit cand and 20 oz bottles. use petg or high heat filiment\u003cbr\u003eWill have to trim a little plastic on the factory center console but it will not be seen\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2006 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eCup Holder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2006\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-03fa09b6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:5425550\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015777054952,"sku":"CAT-03fa09b6","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/cup-holder-1_1778307231837_i422on.jpg?v=1793141269"},{"product_id":"cup-holder-liner-2007-2013-chevrolet-silverado","title":"Cup Holder Liner – 2007-2013 Chevrolet Silverado","description":"\u003cp\u003e3D-printed cup holder liner for the 2007-2013 Chevrolet Silverado, made to order as an affordable alternative to a discontinued or expensive original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eEbay wanted 15 bucks for these. I printed them to match the color of my truck. Should fit Silverado Sierra 07-13 models.\u003cbr\u003eI printed in TPU.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2007-2013 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eCup Holder Liner\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2007\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-a9d0fc84\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:7292384\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015777284328,"sku":"CAT-a9d0fc84","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/cup-holder-liner-1_1778052498743_615uuq.jpg?v=1793141273"},{"product_id":"double-din-radio-bezel-2007-chevrolet-silverado","title":"Double Din Radio Bezel – 2007 Chevrolet Silverado","description":"\u003cp\u003eNeed a replacement double din radio bezel for your 2007 Chevrolet Silverado? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eMade to work with Scosche ICGM10BN on my Chevy Silverado. I didn't like the gaps at the top of the bezel and wanted a different look.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2007 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eDouble Din Radio Bezel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2007\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-a958c3a2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003ePrinter\u003cbr\u003eBrand: Creality\u003cbr\u003ePrinter: Ender-3 v2\u003cbr\u003eRafts: No Supports: No Resolution: 24 Infill: 15 Filament Material: PETG\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:7080965\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015777382632,"sku":"CAT-a958c3a2","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/double-din-radio-bezel-1_1768158478353_ahyvrm.jpg?v=1793141271"},{"product_id":"dual-sunglasses-holder-2007-2013-chevrolet-silverado","title":"Dual Sunglasses Holder – 2007-2013 Chevrolet Silverado","description":"\u003cp\u003e3D-printed replacement dual sunglasses holder made for the 2007-2013 Chevrolet Silverado: a simple way to replace a cracked, lost or hard-to-find original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eRemix of Malamaker's great USB Mount:\u003cbr\u003e\u003cbr\u003ehttps:\/\/cults3d.com\/en\/3d-model\/various\/2007-2013-chevrolet-silverado-cubby-hole-usb-mount\u003cbr\u003e\u003cbr\u003eI wanted something I could hang glasses from in my 2009 Silverado.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2007-2013 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eDual Sunglasses Holder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2007\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-7b728ef6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:6882019\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015777612008,"sku":"CAT-7b728ef6","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/dual-sunglasses-holder-1_1778307225380_jbiad8.jpg?v=1793141272"},{"product_id":"seat-recline-lever-2007-chevrolet-silverado","title":"Seat Recline Lever – 2007 Chevrolet Silverado","description":"\u003cp\u003eNeed a replacement seat recline lever for your 2007 Chevrolet Silverado? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eReplacement seat recline lever for 2007-up Silverado.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2007 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eSeat Recline Lever\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2007\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e2 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-bf9d839e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4746896\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015777710312,"sku":"CAT-bf9d839e","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/seat-recline-lever-1_1783505919339_uvrubj.jpg?v=1793141273"},{"product_id":"microphone-adapter-2009-chevrolet-silverado","title":"Microphone Adapter – 2009 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing microphone adapter on your 2009 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eLong ago, I upgraded the head unit in my 09 Silverado to an aftermarket unit that included an external Microphone for hands-free bluetooth calling. I was always annoyed that these manufactures could never figure out how to use the OEM mic hidden in the overhead console to help get a better \"stealth\" install.\u003cbr\u003eRecently, I upgraded the head unit again to an Eonon Android-based one because I wanted Apply CarPlay. But it too required installation of an ugly external mic. This time, I wanted to get that fully stealth setup.\u003cbr\u003eFirst, I tried using the OEM mic by cutting the oem plug off and soldering on a generic plug. This worked but the sound quality stunk (a common complaint with them by many GM\/Chevy owners). Part of the problem could be that if you look inside it, the mic hardware is sitting sideways. Seems kind of dumb. And who know the quality of the mic they used.\u003cbr\u003eAfter comparing the sound quality of the aftermarket mic, I decided it was the one to use. I fabricated this part to clip into the OEM location but having the mic down fire right into the cabin. This required extracting the actual mic hardware from the plastic housing mount which was simple. Once I did that, I was able to get measurements for the mic itself - about 10mm.\u003cbr\u003eNote that I have uploaded both the \"cut\" version with a 10.5mm hole for my mic and an \"uncut\" version that is solid so you can edit or simply drill out for you mic if it is a different size.\u003cbr\u003eWith this, the sound quality is significantly better.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2009 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eMicrophone Adapter\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2009\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e2 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-6a142ef2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:6719982\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015777972456,"sku":"CAT-6a142ef2","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/microphone-adapter-1_1768164613876_9iwqr9.jpg?v=1793141274"},{"product_id":"door-lock-knob-2010-chevrolet-silverado","title":"Door Lock Knob – 2010 Chevrolet Silverado","description":"\u003cp\u003eNeed a replacement door lock knob for your 2010 Chevrolet Silverado? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eLock knob for my 2010 Chevrolet Silverado. It also works for other GM vehicles.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2010 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eDoor Lock Knob\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2010\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-dd2cb216\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:5063289\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015778234600,"sku":"CAT-dd2cb216","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/door-lock-knob-1_1783490986084_a5qdo8.jpg?v=1793141276"},{"product_id":"dash-change-holder-2011-chevrolet-silverado","title":"Dash Change Holder – 2011 Chevrolet Silverado","description":"\u003cp\u003e3D-printed replacement dash change holder made for the 2011 Chevrolet Silverado: a simple way to replace a cracked, lost or hard-to-find original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis cubby is on the right side of the center cluster. In higher-end (AKA loaded!) trucks some controls go here. But for many of us who don't pay $80K for a vehicle, these are little cubby holes that are useless. So I measured it, went through several fittings and finally came up with this. It works in most materials. I used TPU because it's exposed to temperature extremes and sunlight.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2011 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eDash Change Holder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2011\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-2c85a229\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003ePrinter\u003cbr\u003eBrand: Creality\u003cbr\u003ePrinter: Ender-3 V3 KE\u003cbr\u003eRafts: No Supports: Yes Infill: 25%\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:6678209\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015778431208,"sku":"CAT-2c85a229","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/dash-change-holder-1_1768165012220_1kf6ia.jpg?v=1793141276"},{"product_id":"seat-adjustment-handle-2011-chevrolet-silverado","title":"Seat Adjustment Handle – 2011 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing seat adjustment handle on your 2011 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003ethis is a seat adjustment handle for a 2011 chevy silverado. I am sure it works on other chevy models. I broke mine and i figured it would be fun to design a new one in cad. I suggest printing it out of ABS  or PETG however i am a curious person so i printed mine out of PLA because i want to see how long it will last in the Texas summer. Also it was winter when i made this and i am not famous for thinking ahead. Ill post a photo of it in my truck later\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2011 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eSeat Adjustment Handle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2011\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-75c53363\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:7339608\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015778660584,"sku":"CAT-75c53363","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/seat-adjustment-handle-1_1778052501759_1ud8l7.jpg?v=1793141277"},{"product_id":"seat-recline-lever-2011-chevrolet-silverado","title":"Seat Recline Lever – 2011 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing seat recline lever on your 2011 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eQuick design to replace the recline lever on my 2011 Silverado.  (right side)\u003cbr\u003ejust mirror it if you need left side.\u003cbr\u003eUses factory metal clip.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2011 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eSeat Recline Lever\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2011\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-26b31411\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4665694\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015778758888,"sku":"CAT-26b31411","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/seat-recline-lever-1_1783515057760_i3jy6b.jpg?v=1793141277"},{"product_id":"windshield-pillar-clip-2011-chevrolet-silverado","title":"Windshield Pillar Clip – 2011 Chevrolet Silverado","description":"\u003cp\u003e3D-printed windshield pillar clip for the 2011 Chevrolet Silverado, made to order as an affordable alternative to a discontinued or expensive original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis is a replacement clip for my 2011 Chevy Silverado windshield pillar clip.  I printed it on TPU to provide the flexibility needed to snap into place.\u003cbr\u003e\u003cbr\u003eI recommend printing with the smooth side up and the clip down, with proper supports, for the best finish.\u003cbr\u003e\u003cbr\u003eYou could take this concept and create more from it.  For instance, I am working on a sunglasses holder that will clip into this location on the pillar.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2011 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eWindshield Pillar Clip\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2011\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-07d3525f\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4286473\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/publicdomain\/zero\/1.0\/\" rel=\"nofollow\"\u003eCC0 1.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015779348712,"sku":"CAT-07d3525f","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/windshield-pillar-clip-1_1778343154959_uq2cr6.jpg?v=1793141278"},{"product_id":"3-switch-mount-2013-chevrolet-silverado","title":"3-switch Mount – 2013 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing 3-switch mount on your 2013 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003egoes in under the radio. it's meant for 3 20mm rocker switches.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2013 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003e3-switch Mount\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2013\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-b7c82034\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:7120509\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015780004072,"sku":"CAT-b7c82034","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/3-switch-mount-1_1783490994979_zpykb0.jpg?v=1793141279"},{"product_id":"dash-cup-holder-filler-2013-chevrolet-silverado","title":"Dash Cup Holder Filler – 2013 Chevrolet Silverado","description":"\u003cp\u003e3D-printed dash cup holder filler for the 2013 Chevrolet Silverado, made to order as an affordable alternative to a discontinued or expensive original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eSimple cup to fill in the hole in the dash by radio. Keeps stuff from falling out\u003cbr\u003e\u003cbr\u003ePrint at a angle to keep front clean looking. Use tree supports.\u003cbr\u003e\u003cbr\u003eAdded a taller version\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2013 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eDash Cup Holder Filler\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2013\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e7 (3MF, OBJ, STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-dca044a5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:7301767\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015780135144,"sku":"CAT-dca044a5","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/dash-cup-holder-filler-1_1783491042013_v6yn8z.jpg?v=1793141280"},{"product_id":"center-console-wireless-charger-mount-2014-2018-chevrolet-silverado","title":"Center Console Wireless Charger Mount – 2014-2018 Chevrolet Silverado","description":"\u003cp\u003e3D-printed replacement center console wireless charger mount made for the 2014-2018 Chevrolet Silverado: a simple way to replace a cracked, lost or hard-to-find original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eRemix of the Iphone holder to hold a wireless charger by the mounting nut of https:\/\/www.amazon.com\/gp\/product\/B0859K19M1\/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8\u0026amp;psc=1 snapped write together.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2014-2018 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eCenter Console Wireless Charger Mount\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2014\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-4a4c4151\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:5329816\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015780200680,"sku":"CAT-4a4c4151","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/center-console-wireless-charger-mount-1_1783491022750_f2iwhy.jpg?v=1793141281"},{"product_id":"fender-flare-extenders-2014-2015-chevrolet-silverado","title":"Fender Flare Extenders – 2014-2015 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing fender flare extenders on your 2014-2015 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eExtenders for aftermarket fender flares on 2014-2015 Chevrolet Silverado to fill gap at bumpers.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2014-2015 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eFender Flare Extenders\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2014\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e2 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-84459ca4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:3132655\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015780757736,"sku":"CAT-84459ca4","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/fender-flare-extenders-1_1783419151079_udiz3m.jpg?v=1793141282"},{"product_id":"hat-mount-bracket-2017-chevrolet-silverado","title":"Hat Mount Bracket – 2017 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing hat mount bracket on your 2017 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eI made this bracket for installing a hat mount in my truck. This way I didn`t have to drill any holes or destroy the roof in any way.This fits a Chevrolet Silverado 2017 and it`s very easy to install.\u003cbr\u003eThe top bracket fits into two already made holes in the overhead compartment, and then I just slid the bottom part underneath it so it sticks into place. I made two holes for attaching the brackets together, but I found out that it`s not necessary.\u003cbr\u003eI printed the top part with only about 55% infill and 2 walls because it`s not the part that gets the most stress.\u003cbr\u003eThe bracket itself I printed with 75% infill and 3 walls.\u003cbr\u003eLayer height: .2mm\u003cbr\u003eNozzle size: .6mm\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2017 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eHat Mount Bracket\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2017\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e2 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-8dc09730\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:6832619\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015780888808,"sku":"CAT-8dc09730","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/hat-mount-bracket-1_1778051697193_5xy5pp.jpg?v=1793141283"},{"product_id":"hitch-receiver-cap-2018-chevrolet-silverado","title":"Hitch Receiver Cap – 2018 Chevrolet Silverado","description":"\u003cp\u003e3D-printed hitch receiver cap for the 2018 Chevrolet Silverado, made to order as an affordable alternative to a discontinued or expensive original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eI made this to fit my 2018 Chevy truck with the OEM hitch receiver. It fits that perfectly. It may fit others too, especially GMC, but no guarantees.\u003cbr\u003e\u003cbr\u003eI made this on a Lulzbot TAZ 6. Thingiverse made me select Mini2 as a submodel before uploading. That is incorrect and irrelevant. I made it on a standard TAZ 6.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2018 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eHitch Receiver Cap\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2018\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-85d70f30\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:3416987\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015781445864,"sku":"CAT-85d70f30","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/hitch-receiver-cap-1_1778348576249_lixicn.jpg?v=1793141284"},{"product_id":"center-console-garbage-cup-insert-2019-2022-chevrolet-silverado","title":"Center Console Garbage Cup Insert – 2019-2022 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing center console garbage cup insert on your 2019-2022 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis is a small cup for garbage or sunflower seeds for the 2019-2022 Chevy Silverado. It fits in the spot between the cup holders.\u003cbr\u003e\u003cbr\u003eI originally printed this in vase mode, but it broke after a few days of use. I reprinted it with standard settings, and it has been working great.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2019-2022 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eCenter Console Garbage Cup Insert\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2019\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-6ea75504\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:5863463\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015781544168,"sku":"CAT-6ea75504","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/center-console-garbage-cup-insert-1_1778051709611_gdytmi.jpg?v=1793141284"},{"product_id":"grille-light-bracket-2019-chevrolet-silverado-lt-trail-boss","title":"Grille Light Bracket – 2019 Chevrolet Silverado (LT Trail Boss)","description":"\u003cp\u003e3D-printed replacement grille light bracket made for the 2019 Chevrolet Silverado (LT Trail Boss): a simple way to replace a cracked, lost or hard-to-find original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003e2019 Chevy Silverado LT Trail Boss Grille Light bracket.  Clips into slots in the grille. \u003cbr\u003e\u003cbr\u003eI used the following lights: https:\/\/www.superbrightleds.com\/moreinfo\/led-wired-bolts\/bolt-beam-12mm-led-light\/1494\/3436\/\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2019 Chevrolet Silverado (LT Trail Boss)\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eGrille Light Bracket\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2019\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-77791ca6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4208344\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015781609704,"sku":"CAT-77791ca6","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/grille-light-bracket-1_1778052474855_r6mnpf.jpg?v=1793141285"},{"product_id":"matt-plug-2019-chevrolet-silverado","title":"Matt Plug – 2019 Chevrolet Silverado","description":"\u003cp\u003eReplace a broken or missing matt plug on your 2019 Chevrolet Silverado with this 3D-printed part, produced to order by PartsRemade.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eIf you're like me and you have Vinyl floors but still want mats, you'll find the the chevy ones have holes for the carpet clips. I designed these to plug the holes and they work great.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2019 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eMatt Plug\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2019\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-bc63f3c6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4500576\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015781740776,"sku":"CAT-bc63f3c6","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/matt-plug-1_1768158543073_h242o9.jpg?v=1793141286"},{"product_id":"jump-seat-rear-vent-plug-2020-chevrolet-silverado","title":"Jump Seat Rear Vent Plug – 2020 Chevrolet Silverado","description":"\u003cp\u003e3D-printed replacement jump seat rear vent plug made for the 2020 Chevrolet Silverado: a simple way to replace a cracked, lost or hard-to-find original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eIf you're like me and you have a Work truck but heaven forbid you have center storage, you can get a take off from a more expensive model. The problem is they have a hole in the rear for the vent port and I don't want things just falling inside my seat. This makes a perfect plug that you can just pop in to cover that hoel.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2020 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eJump Seat Rear Vent Plug\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2020\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-56d9e46b\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eRafts:\u003cbr\u003eNo\u003cbr\u003eSupports: Yes\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:7076194\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015781871848,"sku":"CAT-56d9e46b","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/jump-seat-rear-vent-plug-1_1768158652539_tx8syz.jpg?v=1793141287"},{"product_id":"center-console-cubby-insert-2021-chevrolet-silverado-lt","title":"Center Console Cubby Insert – 2021 Chevrolet Silverado (LT)","description":"\u003cp\u003eNeed a replacement center console cubby insert for your 2021 Chevrolet Silverado (LT)? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis is a cubby for the center consol of a 2021 Chevy silverado(between cup holders for change and other stuff.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2021 Chevrolet Silverado (LT)\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eCenter Console Cubby Insert\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2021\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e1 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-a5f899b5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:6576975\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015781937384,"sku":"CAT-a5f899b5","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/center-console-cubby-insert-1_1783490982119_8j7w5k.jpg?v=1793141288"},{"product_id":"cup-holder-can-adapter-2023-chevrolet-silverado","title":"Cup Holder Can Adapter – 2023 Chevrolet Silverado","description":"\u003cp\u003eNeed a replacement cup holder can adapter for your 2023 Chevrolet Silverado? This 3D-printed part is made to order to replace a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eThis is a very simple adapter I created to solve the problem of slim 12oz energy drink cans not staying upright in my truck's cup holder.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2023 Chevrolet Silverado\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before ordering. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eCup Holder Can Adapter\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eSilverado\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2023\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProduction\u003c\/th\u003e\n\u003ctd\u003e3D printed to order (FDM)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign files\u003c\/th\u003e\n\u003ctd\u003e3 (STEP, STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-2a41a446\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eHow to order\u003c\/h2\u003e\u003cp\u003eThis part is in our catalogue and is printed on request. \u003ca href=\"\/pages\/contact\"\u003eSend us a request\u003c\/a\u003e with your vehicle details and we will reply with a price and delivery time.\u003c\/p\u003e\u003ch2\u003eMore Chevrolet parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/chevrolet-parts\"\u003eChevrolet replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D-printed car parts catalogue\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:6926775\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68015782953192,"sku":"CAT-2a41a446","price":1.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/cup-holder-can-adapter-1_1778052466943_tk3fmc.jpg?v=1793141290"}],"url":"https:\/\/partsremade.com\/collections\/chevrolet-silverado-parts.oembed","provider":"PartsRemade","version":"1.0","type":"link"}