{"product_id":"brake-pressure-bleed-adapter-1995-toyota-tacoma","title":"Brake Pressure Bleed Adapter – 1995 Toyota Tacoma","description":"\u003cp\u003e3D printable replacement brake pressure bleed adapter made for the 1995 Toyota Tacoma: download the STL file and print a replacement for a cracked, lost or hard-to-find original part.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003eEdit: I have had really spotty results getting this to seal so I need to change it to \"work in progress\".  Might be simpler and more reliable to buy the commercial tool.  If anyone comes up with a sealing method that is bulletproof with this please post a comment.\u003cbr\u003e\u003cbr\u003e\u003cbr\u003e\u003cbr\u003eThis thing is an adapter to enable you to connect up threaded Euro 45mm brake reservoir pressure bleeder cap to your Toyota Tacoma (and perhaps some other models) instead of having to use a mega cumbersome \"universal\" adapter.  Use with a typical air bleeder hand pump, converted garden sprayer pump, or connect up to your shop air compressor... in which case make sure to run it just enough to get to 10 to 15 psi or so then turn it off and use the air saved in the tank.\u003cbr\u003e\u003cbr\u003eThe way I use this is as an air source only, not to connect up to a tank of brake fluid.  IOW, fill the truck's reservoir to the very top, pressurize it with this setup, bleed the brakes until the fluid gets low in the reservoir, then stop to refill it.  Repeat until done.\u003cbr\u003e\u003cbr\u003eYou can also print a cap and barb here... or use the commercially available one which actually works better because it has a swivel built into the fitting that makes installing and removing the cap easier. If you print the cap and barb they will have to be glued together.  I couldn't get a perfect seal using the printed TPU gasket so it would be better to make one out of neoprene.\u003cbr\u003e\u003cbr\u003ePro tip: use Oetiker clamps and medical quick connect fitting on your air lines.\u003cbr\u003e\u003cbr\u003eThis is not associated with Motive products in any way.  That is just the bleeder I happen to have.\u003cbr\u003e\u003cbr\u003eEdit: made a minor change 4\/12 to make the slots in the adapter shorter to make it easier for the neoprene rubber to cover them entirely.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e1995 Toyota Tacoma\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before printing. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eBrake Pressure Bleed Adapter\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eToyota\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eTacoma\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e1995\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFormat\u003c\/th\u003e\n\u003ctd\u003eDigital download – STL file for FDM 3D printing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFiles included\u003c\/th\u003e\n\u003ctd\u003e4 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-b3af65f9\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eWhat you get\u003c\/h2\u003e\u003cp\u003eA digital 3D model (STL file) of this part, ready to print on your own 3D printer or at any local print shop or online printing service. This is a digital download: no physical part is shipped. Not sure it fits your car? \u003ca href=\"\/pages\/contact\"\u003eContact us\u003c\/a\u003e with your vehicle details before you buy.\u003c\/p\u003e\u003ch2\u003eMore Toyota parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/toyota-parts\"\u003eToyota replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D printable car parts library\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:4818233\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by\/4.0\/\" rel=\"nofollow\"\u003eCC BY-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68038549831912,"sku":"CAT-b3af65f9","price":9.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/brake-pressure-bleed-adapter-1_1783520979159_ejt91b.jpg?v=1793182112","url":"https:\/\/partsremade.com\/products\/brake-pressure-bleed-adapter-1995-toyota-tacoma","provider":"PartsRemade","version":"1.0","type":"link"}