{"product_id":"license-plate-holder-mount-2021-2025-tesla-model-x","title":"License Plate Holder \/ Mount – 2021-2025 Tesla Model X","description":"\u003cp\u003eNeed a replacement license plate holder \/ mount for your 2021-2025 Tesla Model X? This 3D model lets you print a replacement for a broken, worn or missing original piece.\u003c\/p\u003e\u003ch2\u003eAbout this part\u003c\/h2\u003e\u003cp\u003e# Tesla Model X License Plate Mount \/ Holder\u003cbr\u003e\u003cbr\u003eI designed a **license plate mount\/holder** for Tesla vehicles, compatible with different international plate sizes.\u003cbr\u003eIt attaches to the **front grille** using screws and nuts.\u003cbr\u003e\u003cbr\u003eThis is the Model X version. It was tested only on \"Palladium\" cars (2021-2025).\u003cbr\u003eIt won't work for the 2025 refresh Model X (MY 2026) due to the front bumper camera.\u003cbr\u003eIt might work on older legacy models.\u003cbr\u003e\u003cbr\u003eThe plate mount is **slightly curved** to follow the car’s design.\u003cbr\u003eIt was originally made for Brazilian plates, but it should also fit **European** and **American** plates:\u003cbr\u003e\u003cbr\u003e* **Mini Mount** → for European 11 cm plates\u003cbr\u003e* **Normal Mount** → for larger plates\u003cbr\u003e\u003cbr\u003e---\u003cbr\u003e\u003cbr\u003e## Parts\u003cbr\u003e\u003cbr\u003e* **Main Holder**\u003cbr\u003e  Fits on the **external side** of the grille.\u003cbr\u003e\u003cbr\u003e* **Bracket**\u003cbr\u003e  Fits on the **inside** of the grille and secures the holder in place.\u003cbr\u003e\u003cbr\u003e* **Curved Plate Mount**\u003cbr\u003e  Two versions are available:\u003cbr\u003e\u003cbr\u003e  * 11 cm × 34 cm\u003cbr\u003e  * 13 cm × 40 cm\u003cbr\u003e    Any plate longer than this (horizontal axis) should still fit.\u003cbr\u003e    Plates taller than 11 cm (vertical axis) won’t fit with short side arms, but should fit with the long arms.\u003cbr\u003e    The part is **symmetrical** and **cut in half** to fit most printers.\u003cbr\u003e    👉 Print **2 pieces** of the chosen size for each car.\u003cbr\u003e\u003cbr\u003e* **Sides (Arms)**\u003cbr\u003e  Connect the plate mount to the holder. Different versions are available depending on the distance you want the plate to be from the grille.\u003cbr\u003e\u003cbr\u003e  * **Short arms** → work only with plates up to 11 cm tall.\u003cbr\u003e  * **Long arms** → required for taller plates (NOT AVAILABLE YET).\u003cbr\u003e\u003cbr\u003e---\u003cbr\u003e\u003cbr\u003e## Printing Instructions\u003cbr\u003e\u003cbr\u003e* **Material**: Use **PETG** or **ABS**.\u003cbr\u003e  ❌ Do not use PLA — it may warp in sunlight.\u003cbr\u003e* **Supports**: Not needed.\u003cbr\u003e* **Infill**: 25% works fine.\u003cbr\u003e\u003cbr\u003e### Printing Orientation\u003cbr\u003e\u003cbr\u003e* **Sides** → print with nut holes facing up.\u003cbr\u003e* **Bracket \u0026amp; Holder** → print with grille-facing side on the bed.\u003cbr\u003e* **Plate Mounts** →\u003cbr\u003e\u003cbr\u003e  * Best: print **standing up** (same orientation as on the car) for smoother curvature.\u003cbr\u003e  * Alternative: can be printed lying down, but curved lines will look rough.\u003cbr\u003e  * ⚠️ Remember: print **two halves** for each car.\u003cbr\u003e\u003cbr\u003e👉 Refer to the attached images for correct printing orientation.\u003cbr\u003e\u003cbr\u003e---\u003cbr\u003e\u003cbr\u003e## Hardware Required\u003cbr\u003e\u003cbr\u003e* **12 × M6×25 mm Socket Head Screws (Allen)**\u003cbr\u003e  *(Black recommended)*\u003cbr\u003e* **12 × M6 nuts**\u003cbr\u003e\u003cbr\u003eOptional:\u003cbr\u003eThe mount is designed to be taped to the plate, but holes are included if you prefer attaching the plate with screws.\u003cbr\u003e\u003cbr\u003e---\u003cbr\u003e\u003cbr\u003e## Assembly Instructions\u003cbr\u003e\u003cbr\u003e1. Assemble the **Sides** into the **Main Holder** using 4 screws and 4 nuts.\u003cbr\u003e2. Prepare the **Bracket** with nuts inserted.\u003cbr\u003e\u003cbr\u003e   * Tip: apply a small strip of tape (Scotch or electrical) behind the bracket to hold nuts in place.\u003cbr\u003e   * Insert 4 screws into the Main Holder and keep your tool handy.\u003cbr\u003e3. Position the Main Holder\/Sides on the grille. Ensure a perfect fit.\u003cbr\u003e\u003cbr\u003e   * Slide the Bracket from the **top of the grille**, behind the Main Holder.\u003cbr\u003e   * Tighten the screws.\u003cbr\u003e4. Attach the **two halves** of the Plate Mount to the installed holder using 4 screws and 4 nuts.\u003cbr\u003e5. Attach the license plate to the Plate Mount.\u003cbr\u003e\u003cbr\u003e   * Recommended: **VHB double-sided tape**.\u003cbr\u003e   * Alternative: use screw holes if your plate has them.\u003cbr\u003e\u003cbr\u003e\u003cbr\u003eHere’s the updated excerpt with your new note included, ready to slot in before the **Warnings** section:\u003cbr\u003e\u003cbr\u003e---\u003cbr\u003e\u003cbr\u003e## Note\u003cbr\u003e\u003cbr\u003eI also have a **legacy Model Y** version available here: [https:\/\/www.thingiverse.com\/thing:7159256](https:\/\/www.thingiverse.com\/thing:7159256)\u003cbr\u003e\u003cbr\u003e---\u003cbr\u003e\u003cbr\u003e## Warnings ⚠️\u003cbr\u003e\u003cbr\u003e* The **long arms for Model X** have not been tested in the final version, but should work.\u003cbr\u003e* The mount is **extremely sturdy**: it will likely damage the **grille** before breaking itself.\u003cbr\u003e\u003cbr\u003e  * Risk: pulling on the plate, impacts from water, branches, etc.\u003cbr\u003e* Long-term durability is still untested.\u003cbr\u003e* Use at your **own responsibility**.\u003c\/p\u003e\u003ch2\u003eCompatible vehicles\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e2021-2025 Tesla Model X\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003csmall\u003eAlways compare with your original part before printing. Fitment can vary by trim level and production date.\u003c\/small\u003e\u003c\/p\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003ePart\u003c\/th\u003e\n\u003ctd\u003eLicense Plate Holder \/ Mount\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003ctd\u003eTesla\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eModel X\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003ctd\u003e2021\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFormat\u003c\/th\u003e\n\u003ctd\u003eDigital download – STL file for FDM 3D printing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFiles included\u003c\/th\u003e\n\u003ctd\u003e6 (STL)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eCAT-20f91c75\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003ePrint settings\u003c\/h2\u003e\u003cp\u003eStandard FDM printing settings:\u003cbr\u003e- Layer height: 0.2mm\u003cbr\u003e- Infill: 70%\u003cbr\u003e- Supports: As needed\u003c\/p\u003e\u003ch2\u003eWhat you get\u003c\/h2\u003e\u003cp\u003eA digital 3D model (STL file) of this part, ready to print on your own 3D printer or at any local print shop or online printing service. This is a digital download: no physical part is shipped. Not sure it fits your car? \u003ca href=\"\/pages\/contact\"\u003eContact us\u003c\/a\u003e with your vehicle details before you buy.\u003c\/p\u003e\u003ch2\u003eMore Tesla parts\u003c\/h2\u003e\u003cp\u003eBrowse all \u003ca href=\"\/collections\/tesla-parts\"\u003eTesla replacement parts\u003c\/a\u003e or search the full \u003ca href=\"\/collections\/parts-catalogue\"\u003e3D printable car parts library\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003csmall\u003eDesign credit: original design on \u003ca href=\"https:\/\/www.thingiverse.com\/thing:7159410\" rel=\"nofollow\"\u003eThingiverse\u003c\/a\u003e, licensed \u003ca href=\"https:\/\/creativecommons.org\/licenses\/by-sa\/4.0\/\" rel=\"nofollow\"\u003eCC BY-SA-4.0\u003c\/a\u003e.\u003c\/small\u003e\u003c\/p\u003e","brand":"PartsRemade","offers":[{"title":"Default Title","offer_id":68037609488616,"sku":"CAT-20f91c75","price":9.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0818\/0252\/6952\/files\/license-plate-holder-mount-1_1778402321410_39iqhg.jpg?v=1793181244","url":"https:\/\/partsremade.com\/products\/license-plate-holder-mount-2021-2025-tesla-model-x","provider":"PartsRemade","version":"1.0","type":"link"}